For a stretch stitch, you will need to use a narrow zigzag stitch. Small adjustments to increase the width from a straight stitch to a zigzag stitch will allow the stitching to stretch with the fabric while sewing a straight seam at the same time.
What is a narrow zig zag stitch?
SEAMS – A very narrow zig zag stitch will give some stretch to the seam and prevent breaking. This is the most commonly sewn seam on leotards and swimwear when you are using your regular machine. TRY – Length 2.5 and width 1.0. FINISHING – Stretch fabric doesn’t fray so you don’t usually need to seam finish the edges.
What tension should I use for zig zag stitch?
The dial settings run from 0 to 9, so 4.5 is generally the ‘default’ position for normal straight-stitch sewing. This should be suitable for most fabrics. If you are doing a zig-zag stitch, or another stitch that has width, then you may find that the bobbin thread is pulled through to the top.
What are zig zag stitches used for?
The most common use of a zigzag stitch is to enclose raw edges as a seam finish. As a seam finish, one edge of the stitch is sewn off the edge of the fabric so that the threads of the fabric are enclosed within the threads of the zigzag stitch making the fabric unable to fray.
Why is my zig zag stitch tunneling?
If the zig-zag stitch width is pretty wide, and the part you are zig-zagging is bunching up under the thread, that is called ‘tunneling’ and you may need a stabilizer . The upper thread should show along the sides of the stitch on the wring side of the fabric when the tension is correctly adjusted.
Is a zigzag stitch stronger than a straight stitch?
Though straight stitch is considered as the strongest stitch, zigzag is one of the most durable stitches. There are ways in which you can make the hold stronger. For instance, the triple zigzag is stronger compared to the ordinary zigzag ones.
What width should my sewing machine be on?
A straight stitch has no width so it makes sense to set the dial at “0”. However, each machine varies so you will want to set the Stitch Width dial at the position where the needle is centered over the stitch plate. This will give you the most accurate seam allowance.
What should my thread tension be?
Remember, most tension discs close when the presser foot is down, so be sure to thread the machine with a raised foot. A good habit is to put the spool on the machine, and pull out 18 inches of thread.
Do I need a zig zag stitch?
One of the most common uses for the zigzag stitch is to sew stretchy materials. When sewing a material that stretches, such as knitted fabrics and neoprene, it’s essential to use a stitch that can stretch with the fabric.
Can you do a zigzag stitch with a walking foot?
Yes, you can use your walking foot for more than straight stitching. A zig-zag stitch should be just fine because all the movement in the stitch pattern is forward. In fact many of the decorative stitches on your sewing machine are just fine to use with your even feed foot installed.
Which stitch is the strongest?
The strongest stitch on a sewing machine is a straight stitch. The straight stitch is very hard to tear, and when combined with tough and long-lasting nylon or polyester thread, we get the most durable result.
Why won’t my sewing machine do a zigzag stitch?
Check the tension on your sewing machine, as too much tension may pull the threads too tightly and loose tension may not pull the threads tight enough. Set it at the middle range and test it from there, trying to make a zigzag stitch using a greater or lesser tension.
What is a 3 step zigzag stitch?
Three-step zigzag: When used on the widest width, the ordinary zigzag stitch pulls the fabric into a tunnel and the fabric rolls under the stitch — not very desirable. … The needle takes three stitches to one side and then three stitches to the other side, keeping the fabric flat and tunnel-free.